1967 Austin 1100 MOT Pass Rate
Pass rate for 1100 models manufactured in 1967, based on 140 real MOT test results.
Data from official DVSA MOT testing records
1967 Austin 1100 MOT Analysis
The 1967 Austin 1100 has an MOT pass rate of 68.6% based on 140 tests — slightly above the UK average for UK vehicles. Cars of this vintage present for MOT with an average of 56,751 miles on the odometer. With a 31.4% failure rate, the 1967 1100 is rated as "Good" for MOT reliability.
The leading cause of MOT failure for the 1967 Austin 1100 is Body, chassis, structure, responsible for 1.4% of failures. Body and structure failures include excessive corrosion, sharp edges, loose panels, and damage to the vehicle frame. Rust is the primary concern, especially on older vehicles or those exposed to road salt. Typical repair costs range from £100–500+. Suspension is the second most common issue at 1.4%. Brakes follows at 0.7%.
Top failures specific to 1967 models only. The overall 1100 page may show different rankings.
What Fails Most
What Fails on This Car?
Click a category to see specific failure items.
View as table
| Rank | Failure Category | Rate (%) | Count |
|---|---|---|---|
| 1 | Body, Chassis, Structure | 1.4% | 2 |
| 2 | Suspension | 1.4% | 2 |
| 3 | Brakes | 0.7% | 1 |
Failures per 10,000 Miles
avg. 56,751 miFor every 10,000 miles driven, this shows what percentage of MOT tests fail for each category. This accounts for how far cars are actually driven, not just raw pass/fail counts.
View as table
| Category | Rate / 10K mi | Raw % | Count |
|---|---|---|---|
| Body & Structure | 0.25 | 1.4% | 2 |
| Suspension | 0.25 | 1.4% | 2 |
| Brakes | 0.13 | 0.7% | 1 |
Mileage Statistics
Mileage-adjusted failure rate — accounts for how much this model year is typically driven.
About This Data
The 1967 Austin 1100 has an MOT pass rate of 68.6% based on 140 tests — slightly above the UK average for UK vehicles. Cars of this vintage present for MOT with an average of 56,751 miles on the odometer. With a 31.4% failure rate, the 1967 1100 is rated as "Good" for MOT reliability.
If you own or are considering buying a 1967 Austin 1100, you can expect reliable MOT performance overall. Before your MOT, pay particular attention to body, chassis, structure: Inspect sills, wheel arches, door bottoms, and the chassis for rust. Surface rust is acceptable but structural corrosion or holes will fail. Check that all doors, bonnet, and boot close securely. At 56,751 average miles, these vehicles are in the mid-range where component wear starts to become a factor.
Body, chassis, structure — 1.4% of failures
Body, chassis, structure issues account for 1.4% of MOT failures on 1967 Austin 1100 models. Body and structure failures include excessive corrosion, sharp edges, loose panels, and damage to the vehicle frame. Rust is the primary concern, especially on older vehicles or those exposed to road salt. Typical repair costs: £100–500+. Pre-MOT check: Inspect sills, wheel arches, door bottoms, and the chassis for rust. Surface rust is acceptable but structural corrosion or holes will fail. Check that all doors, bonnet, and boot close securely.
Suspension — 1.4% of failures
Suspension issues account for 1.4% of MOT failures on 1967 Austin 1100 models. Suspension failures typically involve worn bushes, leaking shock absorbers, broken coil springs, and damaged suspension arms. These affect ride quality, tyre wear, and road holding. Typical repair costs: £200–500. Pre-MOT check: Look for uneven tyre wear, listen for clunking over bumps, and check if the car pulls to one side. A bouncy ride suggests worn shock absorbers. Visually inspect coil springs for cracks.
Brakes — 0.7% of failures
Brakes issues account for 0.7% of MOT failures on 1967 Austin 1100 models. Brake-related failures include worn brake pads, corroded brake discs, leaking brake lines, and faulty brake servos. These are safety-critical components — any brake deficiency will result in an MOT fail. Typical repair costs: £150–400. Pre-MOT check: Listen for squealing or grinding noises. Check brake pedal feel — if it feels spongy or goes to the floor, have the system inspected immediately. Look at brake pad thickness through the wheel spokes (minimum 3mm).
Based on DVSA anonymised MOT test data (2005–2024). Crown copyright, Open Government Licence v3.0.